Текущее время: 28 мар 2024, 20:19



Ответить на тему  [ Сообщений: 69 ]  На страницу Пред.  1, 2, 3, 4  След.
 FLHRCI Road King 2003 
Автор Сообщение

Зарегистрирован: 17 янв 2012, 13:00
Сообщения: 141
Откуда: Москва Бабушкинская
Мотоцикл(ы): FLHRCI 2003
Непрочитанное сообщение Re: FLHRCI Road King 2003
С колесом все отлично. Очень аккуратно выправили - как новое.


06 июн 2012, 09:38
Профиль
МОДЕРАТОР

Зарегистрирован: 01 апр 2011, 06:08
Сообщения: 3574
Откуда: Омск-падла-сити
Мотоцикл(ы): FLHTCUI'08, WLA bobber
Непрочитанное сообщение Re: FLHRCI Road King 2003
Пиши кто. Партизан! А то занесет кого-нить в Падла-сити и небудут знать где можно справить то-сё.
Да и на FLHX стоят спицы...


06 июн 2012, 12:26
Профиль

Зарегистрирован: 17 янв 2012, 13:00
Сообщения: 141
Откуда: Москва Бабушкинская
Мотоцикл(ы): FLHRCI 2003
Непрочитанное сообщение Re: FLHRCI Road King 2003
Это не секрет конечно. Все он же - Степа Троицкий. Мотомастерская 45club.ru. Мне понравилось, как работает - быстро, аккуратно и качественно. Но я совсем начинающий байкер, моя оценка может быть и не столь компетентна.
И вообще, Костя, пока ты не исчез с карты РФ, выехал бы, поучил чайника харлеем рулить! А то тут вокруг одни пластики, а они кагбэ совсем из другого мира..


06 июн 2012, 13:14
Профиль

Зарегистрирован: 10 апр 2012, 19:38
Сообщения: 61
Откуда: Таллинн Est
Мотоцикл(ы): FLHRI 2003
Непрочитанное сообщение Re: FLHRCI Road King 2003
:D :D так это мы уже после больницы в гараж к нему поехали он просил помочь движок после переборки на место поставить двигло красивое шовел хед 83его года


12 июн 2012, 00:49
Профиль

Зарегистрирован: 17 янв 2012, 13:00
Сообщения: 141
Откуда: Москва Бабушкинская
Мотоцикл(ы): FLHRCI 2003
Непрочитанное сообщение Re: FLHRCI Road King 2003
Сегодня случилась странная вещь. Катал на площадке с часик на низкой передаче, отрабатывал на фишках упражнения. Обратил внимание, что горит лампочка топлива. Поехал заправляться, заправка была недалеко. И где-то через километр после площадки, на скорости миль 50 вырубился мотор. Как-будто горючка закончилась. Осторожно выкатил на обочину, до заправки метров 600, во думаю невезуха! Попробовал снова запустить мотор - тут же завелся! Очкуя, тихонько доехал до заправки, стараясь держать невысокие обороты. На заправке до горлышка залилось только 15 литров!!!! Четыре литра там точно еще было!!!! После заправки катал еще час-полтора, никаких проблем!!! Что за ерунда??? У кого-нибудь было такое?


08 июл 2012, 21:09
Профиль
МОДЕРАТОР

Зарегистрирован: 01 апр 2011, 06:08
Сообщения: 3574
Откуда: Омск-падла-сити
Мотоцикл(ы): FLHTCUI'08, WLA bobber
Непрочитанное сообщение Re: FLHRCI Road King 2003
Привет! Чойта я все выхи лётал по ентай площадке- падла-сити, тебя дружище невидал. :lol:
А по теме. Есть подозрение-посмотри ошибки, мне помогло. А еще очень похоже на клемму отпадающую от аккумуля. Свет и всё-всё-всё пропало в момент вырубания или нет?


09 июл 2012, 05:40
Профиль

Зарегистрирован: 17 янв 2012, 13:00
Сообщения: 141
Откуда: Москва Бабушкинская
Мотоцикл(ы): FLHRCI 2003
Непрочитанное сообщение Re: FLHRCI Road King 2003
Ты, наверное, высоко лётал. :D Я же - низехонько так, по обочинкам, пугаясь встречного транспорта. Да и пасся я в основном у Арены. Еще вчера задолбался мойку искать - колеса хочу от этой синей фигни нормально керхером смыть. То толпы народа, то испуганно реагируют на вопрос о мойке мотоцикла. Даже в Аларм-сервис заехал, вроде как понтовые ребята, может не испугаются. Действительно, не испугались, но у них ОЧЕРЕДЬ, ПО ЗАПИСИ на два дня вперед. Притом, что мойка там стоит в 3 раза дороже нормальной цены. Короче, не понятно, где в этом городе помыться можно.

Про ошибки - не понял. Что и куда смотреть? Ничего нового на приборке не загоралось, свет и всё-всё-всё в момент вырубания не пропадали. Поэтому и показалось, что как-будто бензин закончился.


09 июл 2012, 07:49
Профиль
МОДЕРАТОР

Зарегистрирован: 01 апр 2011, 06:08
Сообщения: 3574
Откуда: Омск-падла-сити
Мотоцикл(ы): FLHTCUI'08, WLA bobber
Непрочитанное сообщение Re: FLHRCI Road King 2003
:cry: а у тебя самодиагностики нет?
Я моюсь в Автоблеске звездова 23/1


09 июл 2012, 07:57
Профиль

Зарегистрирован: 17 янв 2012, 13:00
Сообщения: 141
Откуда: Москва Бабушкинская
Мотоцикл(ы): FLHRCI 2003
Непрочитанное сообщение Re: FLHRCI Road King 2003
LowriderRF писал(а):
:cry: а у тебя самодиагностики нет?
А черт его знает. А это как? Что нажимать?


09 июл 2012, 08:28
Профиль
МОДЕРАТОР

Зарегистрирован: 01 апр 2011, 06:08
Сообщения: 3574
Откуда: Омск-падла-сити
Мотоцикл(ы): FLHTCUI'08, WLA bobber
Непрочитанное сообщение Re: FLHRCI Road King 2003
Re: Diagnostic codes for 2003 Road King?
1. Remove right side saddlebag and side cover if so equipped. Remove protective plug from data link connector.

2. To activate the diagnostic feature, proceed as follows:
a. Create diagnostic test wire or use a female spade clip.
b. Install diagnostic test wire across Terminals 1 and 2 on the data link connector.
c. Turn Ignition/Light Key Switch to IGNITION and wait approximately 10 seconds (4 seconds lamp ON, 6 seconds lamp OFF) for check engine lamp to start flashing.

3. All trouble codes are sent out as a series of flashes. To retrieve the first digit of the trouble code simply observe the number of times the lamp flashes.
a. The lamp will then flash one or more times to indicate the first digit of the trouble code.

b. The length of time the lamp is illuminated and the length of time in which it is off are each about 0.5 second in duration.

4. The second digit follows:
a. Following the transmission of the first digit, there is a 1.2 second pause in which the lamp is off.
b. The lamp will then flash one or more times to indicate the second digit of the trouble code. Count the number of times the lamp flashes to retrieve the second digit.

5. If more than one trouble code is sent:
a. Following transmission of the second digit of the first code, there is a 3 second pause in which the lamp is off.
b. Once all codes have been sent, the data string is repeated. When you have recorded the same trouble code twice, it is an indication that the transmission has been restarted and that all trouble codes have been retrieved.

IMPORTANT NOTE ..If diagnostic test wire is installed across Pins 1 and 2 on connector in lieu of a Scanalyzer, the ECM is placed in a diagnostic test mode and the engine will start. The test wire must be removed from the data connector and the ignition switch turned OFF or the check engine lamp will continue to flash codes. A historic trouble code resides in the memory of the ECM until the code is cleared by use of the Scanalyzer or a total of 50 trips has elapsed. A “trip” consists of a start and run cycle, the run cycle lasting at least 30 seconds. After the 50 trip retention period, the trouble code is automatically erased from memory (that is, assuming no subsequent faults of the same type are detected in that period). The numbers after the 'historic' or 'current' is the speedo code number, but without the electrical diognostics manual you're peeing into the wind.

1 Current 53 ECM flash error
2 Historic 53 ECM flash error
3 Current 54 ECM EEPROM error
4 Historic 54 ECM EEPROM error
5 Current 63 ECM serial data low
6 Current 63 ECM serial data open/high
7 Current 63 TSSM serial data low
8 Current 63 TSSM serial data open/high
9 Current 61 Loss of TSM/TSSM serial data
10 Current 14 Loss of all ECM serial data (state of health)
10 24 Loss of vehicle speed
10 33 Loss of vehicle inhibit motion
10 43 Loss of power train security status
11 Current 33 System relay contacts open
12 Current 33 System relay coil high/shorted
13 Current 33 System relay coil open/low
14 Current 33 System relay contacts closed
15 Current 99 Incorrect password
16 Current 99 Missing password
17 Current 41 CKP sensor intermittent
18 Current 41 CKP sensor synch error
19 Current 11 TP sensor open/low
20 Current 11 TP sensor high
21 Current 12 MAP sensor open/low
22 Current 12 MAP sensor high
23 Current 14 ET sensor voltage low
24 Current 14 ET sensor open/high
25 Current 15 IAT sensor voltage low
26 Current 15 IAT sensor open/high
27 Current 24 Front ignition coil open/low
28 Current 25 Rear ignition coil open/low
29 Current 24 Front ignition coil high/shorted
30 Current 25 Rear ignition coil high/shorted
31 Current 24 Front cylinder combustion intermittent
32 Current 25 Rear cylinder combustion intermittent
33 Current 23 Front injector open/low
34 Current 32 Rear injector open/low
35 Current 23 Front injector high
36 Current 32 Rear injector high
37 Current 16 Battery voltage low
38 Current 16 Battery voltage high
39 Current 43 VSS sensor low
40 Current 43 VSS sensor high
41 Current N/A (no speedo code for this) Check engine light open/low NO CHECK ENGINE LAMP AT KEY ON or CHECK ENGINE LAMP ON CONTINUOUSLY
42 Current N/A (no speedo code for this) Check engine light high NO CHECK ENGINE LAMP AT KEY ON
43 Current 35 Tachometer low
44 Current 35 Tachometer high
45 Current 25 Rear cylinder no combustion
46 Current 24 Front cylinder no combustion
47 Current 34 Loss of idle speed control IDLE AIR CONTROL
48 Current 35 Accelerometer fault
49 Current 34 Starter output high
50 Current 25 Ignition enable output high
51 Current 21 Left turn output fault
52 Current 22 Right turn output fault
53 Current 11 Battery voltage high
54 Current 31 Alarm output low
55 Current 32 Alarm output high
56 Current 41 Ignition switch open/low
57 Historic 63 ECM serial data low
58 Historic 63 ECM serial data open/high
59 Historic 63 TSSM serial data low
60 Historic 63 TSSM serial data open/high
61 Historic 61 Loss of TSM/TSSM serial data
62 Historic 14 Loss of all ECM serial data (state of health)
63 Historic 33 System relay contacts open
64 Historic 33 System relay coil high/shorted
65 Historic 33 System relay coil open/low
66 Historic 33 System relay contacts closed
67 Historic 99 Incorrect password
68 Historic 99 Missing password
69 Historic 41 CKP sensor intermittent
70 Historic 41 CKP sensor synch error
71 Historic 11 TP sensor open/low
72 Historic 11 TP sensor high
73 Historic 12 MAP sensor open/low
74 Historic 12 MAP sensor high
75 Historic 14 ET sensor voltage low
76 Historic 14 ET sensor open/high
77 Historic 15 IAT sensor voltage low
78 Historic 15 IAT sensor open/high
79 Historic 24 Front ignition coil open/low
80 Historic 25 Rear ignition coil open/low
81 Historic 24 Front ignition coil high/shorted
82 Historic 25 Rear ignition coil high/shorted
83 Historic 24 Front cylinder combustion intermittent
84 Historic 25 Rear cylinder combustion intermittent
85 Historic 23 Front injector open/low
86 Historic 32 Rear injector open/low
87 Historic 23 Front injector high
88 Historic 32 Rear injector high
89 Historic 16 Battery voltage low
90 Historic 16 Battery voltage high
91 Historic 43 VSS sensor low
92 Historic 43 VSS sensor high
93 Historic N/A Check engine light open/low NO CHECK ENGINE LAMP AT KEY ON or CHECK ENGINE LAMP ON CONTINUOUSLY
94 Historic N/A Check engine light high NO CHECK ENGINE LAMP AT KEY ON
95 Historic 35 Tachometer low
96 Historic 35 Tachometer high
97 Historic 25 Rear cylinder no combustion
98 Historic 24 Front cylinder no combustion
99 Historic 34 Loss of idle speed control
100 Historic 35 Accelerometer fault
101 Historic 34 Starter output high
102 Historic 25 Ignition enable output high
103 Historic 21 Left turn output fault
104 Historic 22 Right turn output fault
105 Historic 11 Battery voltage high
106 Historic 31 Alarm output low
107 Historic 32 Alarm output high
108 Historic 41 Ignition switch open/low


09 июл 2012, 08:47
Профиль
МОДЕРАТОР

Зарегистрирован: 01 апр 2011, 06:08
Сообщения: 3574
Откуда: Омск-падла-сити
Мотоцикл(ы): FLHTCUI'08, WLA bobber
Непрочитанное сообщение Re: FLHRCI Road King 2003
That was for the 00-03 bikes, this is for the 04 to present ones with the serial bus setup

The IM (instrument module) is capable of displaying DTC's (diagnostic trouble codes).
Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC).

1- Turn Ignition switch to OFF & Run/Stop switch is to Run.

2- Push odometer reset button in & hold.

3- Turn ignition switch to Ignition and release odometer reset button. Background lighting sould illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear.

4 - Push the odometer reset button once and you will see the selection menu "PSSPt" with the first P flashing.

5 - Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t and back to P, etc.)
P = ECM/ICM (Electronic Control Module [EFI] / Ignition Control Module [Carbureted])
S = TSM/TSSM (Turn Signal/ Turn Signal Security Module)
SP = speedometer
T = tachometer

6 - To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTC’s the code will be displayed or the word “none” will appear if there are no DTC’s. Push the odometer reset button again to view additional codes if they exist.

7 - Record the codes.

8 - If DTC’s are not to be cleared, Press and release the odometer reset button. Part number of module will be displayed.
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until 'clear' comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9. If the code is current it will reappear.

9 – Press and release the odometer reset button to continue to the next module.

10 – Turn Ignition switch to OFF.

--------------------------

DTC FAULT CONDITION MODULE

B0563 Battery Voltage High TSM/TSSM
B1004 Fuel Level Sending Unit Low Instruments
B1005 Fuel Level Sending Unit High/Open Instruments
B1006 Accessory Line Overvoltage Instruments
B1007 Ignition Line Overvoltage Instruments
B1008 Reset Switch Closed Instruments
B1131 Alarm Output Low TSM/TSSM
B1132 Alarm Output High TSM/TSSM
B1134 Starter Output High TSM/TSSM
B1135 Accelerometer Fault TSM/TSSM
B1151 Sidecar BAS Low TSM/TSSM
B1152 Sidecar BAS High TSM/TSSM
B1153 Sidecar BAS Out of Range TSM/TSSM
P0106 MAP Sensor Rate of Range Error Carb
P0107 Map Sensor Failed Open/Low Carb
P0107 Map Sensor Open/Low EFI
P0108 Map Sensor Failed High Carb
P0108 Map Sensor High EFI
P0112 IAT Sensor Voltage Low EFI
P0113 IAT Sensor Voltage Open/High EFI
P0117 ET Sensor Voltage Low EFI
P0118 ET Sensor Voltage Open/High EFI
P0122 TP Sensor Open/Low EFI
P0123 TP Sensor High EFI
P0261 Front Injector Open/Low EFI
P0262 Front Injector High EFI
P0263 Rear Injector Open/Low EFI
P0264 Rear Injector High EFI
P0373 CKP Sensor Intermittent Carb
P0373 CKP Sensor Intermittent EFI
P0374 CKP Sensor Not Detected Carb
P0374 CKP Sensor Synch Error EFI
P0501 VSS Low Carb
P0501 VSS Low EFI
P0502 VSS High/Open Carb
P0502 VSS High/Open EFI
P0505 Loss of Idle Sped Control EFI
P0562 Battery Voltage Low Carb
P0562 Battery Voltage Low EFI
P0563 Battery Voltage High Carb
P0563 Battery Voltage High EFI
P0602 Calibration Memory Error Carb
P0603 EEPROM Failure Carb
P0603 ECM EEPROM Error EFI
P0604 RAM Failure Carb
P0605 Program Memory Error Carb
P0605 ECM Flash Error EFI
P0607 Converter Error Carb
P1001 System Relay Coil Open/Low EFI
P1002 System relay Coil High/Shorted EFI
P1003 System relay Contacts Open EFI
P1004 System Relay Contacts Closed EFI
P1009 Incorrect Password Carb
P1009 Incorrect Password EFI
P1010 Missing Password Carb
P1010 Missing Password EFI
P1351 Front Ignition Open/Low Carb
P1351 Front Ignition Open/Low EFI
P1352 Front Ignition Coil High/Shorted Carb
P1352 Front Ignition Coil High/Shorted EFI
P1353 Front Cylinder No Combustion EFI
P1354 Rear Ignition Coil Open/Low Carb
P1354 Rear Ignition Coil Open/Low EFI
P1355 Rear Ignition Coil High/Shorted Carb
P1355 Rear Ignition Coil High/Shorted EFI
P1356 Rear Cylinder No Combustion EFI
P1357 Intermittent Secondary Front EFI
P1358 Intermittent Secondary Rear EFI
U1016 Loss of ICM/ECM Serial Data Instruments
U1016 Loss of ECM Serial Data, Vehicle Speed, Vehicle Inhibit Motion or Powertrain Security Status TSM/TSSM
U1064 Loss of TSM/TSSM Serial Data Carb
U1064 Loss of TSM/TSSM Serial Data EFI
U1064 Loss of TSM/TSSM Serial Data Instruments
U1097 Loss of Speedometer Serial data Carb
U1097 Loss of Speedometer Serial data EFI
U1097 Loss of Speedometer Serial data TSM/TSSM
U1255 Missing Message at Speedometer EFI
U1255 Serial Data Error/Missing Message EFI
U1255 Serial Data Error/Missing Message Instruments
U1255 Serial Data Error/Missing Message TSM/TSSM
U1300 Serial Data Low Carb
U1300 Serial Data Low EFI
U1300 Serial Data Low Instruments
U1300 Serial Data Low TSM/TSSM
U1301 Serial Data Open/High Carb
U1301 Serial Data Open/High EFI
U1301 Serial Data Open/High Instruments
U1301 Serial Data Open/High TSM/TSSM


2006 models with 02 sensors (Dynas)

P0131 Front 02 sensor lean for any length of time
P0151 Rear 02 sensor lean for any length of time
Above codes can also be set if 02 sensor fails.
-----------------------

AFR – Air Fuel Ratio

ATS – Air Temperature Sensor

BAS – Bank Angle Sensor

CCM – Cruise Control Module

CKP – Crank Position Sensor. The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed. Home position established by taking readings off the 22 teeth on the alternator rotor.

DTC – Diagnostic Trouble Codes

ECM – Electronic Control Module. (The Computer) Computes the spark advance for proper ignition timing and fuel control based on sensor inputs (from CKP, MAP & TP sensors) and controls the low-voltage circuits for the ignition coils and injectors. The dwell time for the ignition coil is also calculated in the microprocessor and is dependent upon battery voltage. The programmed dwell feature gives adequate spark at all speeds.

ECT – Engine Coolant Temperature. Sensor also controls the cooling fan relay that provides 12 Vdc to the fans.

EFI – Electronic Fuel Injection

EFP – Electronic Fuel Pump

ET – Engine Temperature sensor

FI – Fuel Injectors

FPR – Fuel Pressure regulator

IAC – Idle Air Control actuator

IAT – Intake Air Temperature sensor

ISS – Ion Sensing System…detonation detection

MAP – manifold Absolute Pressure sensor. The MAP sensor monitors the intake manifold pressure (vacuum) and sends the information to the ECM. The EMC then adjusts the spark and fuel-timing advance curves for optimum performance.

TP – Throttle Position Sensor

TSM/TSSM (Turn Signal/ Turn Signal Security Module)

VE – Volume Efficiency

VSS – Vehicle Speed Sensor. Used as an input for idle speed control


09 июл 2012, 08:51
Профиль
МОДЕРАТОР

Зарегистрирован: 01 апр 2011, 06:08
Сообщения: 3574
Откуда: Омск-падла-сити
Мотоцикл(ы): FLHTCUI'08, WLA bobber
Непрочитанное сообщение Re: FLHRCI Road King 2003
Стырено тут: http://www.hdtalking.com/touring_models/627-diagnostic_codes_for_2003_road_king.html


09 июл 2012, 08:51
Профиль

Зарегистрирован: 10 апр 2012, 19:38
Сообщения: 61
Откуда: Таллинн Est
Мотоцикл(ы): FLHRI 2003
Непрочитанное сообщение Re: FLHRCI Road King 2003
я так понимаю нужен какой то дата кабель для подключения к компу? и програмное обеспечение... а мммм где это взять? был в хорватии и возникла такая непонятность после заведения мотора загоралась лампочка engine потом через какое то время гасла... вернулся в эстонщину перестала загораться, есть подозрение на масло, может для нашего климата оно и нормальное но в той жаре оно не выполняет своих функций... я там проверял уровень когда, то масло по своей консистенции напоминало обычный чай... водичка... пользовал масло GULF что скажете про LIQUI MOLY?


09 июл 2012, 11:41
Профиль
МОДЕРАТОР

Зарегистрирован: 01 апр 2011, 06:08
Сообщения: 3574
Откуда: Омск-падла-сити
Мотоцикл(ы): FLHTCUI'08, WLA bobber
Непрочитанное сообщение Re: FLHRCI Road King 2003
Re: диагностические коды на 2003 год Road King?
1. Удалить справа подседельную боковую крышку, если таковая имеется. Удалите защитную заглушку с разъема передачи данных.

2. Чтобы активировать диагностические функции, выполните следующие действия:
а. Создать диагностический тест провод или использовать женский клип лопатой( :lol: онлайн перевод жесть!).
б. Установить диагностический тест провод через терминалы 1 и 2 разъема передачи данных.
в. Включите зажигание / Light Key Switch для зажигания и подождите примерно 10 секунд (4 секунды лампа ON, 6 секунд лампа OFF) для проверки двигателя лампа начинает мигать.

3. Все коды ошибок посылаются в виде серии вспышек. Для получения первой цифры кодов неисправностей просто наблюдать, сколько раз мигает.
а.Лампа будет мигать один или несколько раз, чтобы указать, первая цифра кодов неисправностей.

б. Период времени, лампа горит и времени, в котором он выключен, каждый примерно 0,5 второй срок.

4. Вторая цифра следующим образом:
а. После передачи первой цифрой, есть 1.2 секунды пауза, в которой не горит.
б.Лампа будет мигать один или несколько раз, чтобы указать, вторая цифра кодов неисправностей. Подсчитайте, сколько раз этот индикатор мигает, чтобы получить вторую цифру....ну и т.д. по тексту...т.е. никакова прибору нинадо, только перемычка.

:lol: если кто чо непонял спрашивайте, переведу переводчиком который в голове. :lol: :lol: :lol: :lol:


09 июл 2012, 11:59
Профиль

Зарегистрирован: 17 янв 2012, 13:00
Сообщения: 141
Откуда: Москва Бабушкинская
Мотоцикл(ы): FLHRCI 2003
Непрочитанное сообщение Re: FLHRCI Road King 2003
Жуть какая. Я понял, в случае чего, пузырь французского коньяка, и к тебе за переводом. :)
Анализировал ситуацию сегодня, и такая мысль закралась: перед тем, как вырубился мотор, я прошел небольшой поворот после горки с приличной скоростью и достаточно сильным наклоном (это после площадки понравилось подножками шкрябать :)) Может быть такое, что остатки топлива в баке перелились и насос глотнул воздуха? После этого проехал метров 300 на том, что осталось в системе, и заглох.. После остановки уровень топлива выровнялся, насос подкачал топливо, и все нормально завелось. Может в этом дело, или я вообще что-то неадекватное тут леплю?


09 июл 2012, 14:57
Профиль

Зарегистрирован: 03 янв 2012, 21:18
Сообщения: 1201
Откуда: Челябинск
Мотоцикл(ы): FLSTFI 2002
Непрочитанное сообщение Re: FLHRCI Road King 2003
у меня так реагирует на кончающееся топливо. Но при заезде на заправку входит примерно 18.5 литров. Т.е. литра 2 остается.


09 июл 2012, 18:12
Профиль ICQ

Зарегистрирован: 10 апр 2012, 19:38
Сообщения: 61
Откуда: Таллинн Est
Мотоцикл(ы): FLHRI 2003
Непрочитанное сообщение Re: FLHRCI Road King 2003
немножко не сообразил что за перемычка??? как она выглёндает??? где моргает лямпочка?


10 июл 2012, 01:00
Профиль
МОДЕРАТОР

Зарегистрирован: 01 апр 2011, 06:08
Сообщения: 3574
Откуда: Омск-падла-сити
Мотоцикл(ы): FLHTCUI'08, WLA bobber
Непрочитанное сообщение Re: FLHRCI Road King 2003
;) Да перестань, какой коньяк? Так просто приезжай, тел знаешь, район где я живу тоже знаешь-помаракуем посмотрим. Мы в 20тых этого месяца в е-бург к официалу собрались стритглайд гнать в ремонт, ибо Тимон пахоже запорол передний горшок(мотик прошел 2080миль)

А перемычка? проводок просто. моргает или поворотниками или лампочка на панели(чек).

Со своих недалеких мозгов согласен. Может просто воздуха хапнул?


10 июл 2012, 05:55
Профиль

Зарегистрирован: 17 янв 2012, 13:00
Сообщения: 141
Откуда: Москва Бабушкинская
Мотоцикл(ы): FLHRCI 2003
Непрочитанное сообщение Re: FLHRCI Road King 2003
Подскажите, кто может, что за ерунда такая - после 20 км езды по городу появляется такой сухой шелест на переднем колесе в тормозном суппорте, как будто колодка немного прижимается к диску. При незначительном нажатии переднего тормоза, звук тут же пропадает. Посмотрел, сама колодка выглядит еще вполне нормально по толщине, да и звук этот появляется не сразу. не хочется сейчас разбирать - совсем немного осталось кататься.. В чем может быть дело? Насколько это критично?


03 сен 2012, 06:00
Профиль

Зарегистрирован: 10 апр 2012, 19:38
Сообщения: 61
Откуда: Таллинн Est
Мотоцикл(ы): FLHRI 2003
Непрочитанное сообщение Re: FLHRCI Road King 2003
у меня такая же ерунда... это просто после нажатия на тормоз колодка не отходит полностью от диска... если я правильно понимаю то, за то чтобы отодвигать колодки взад отвечают манжеты а они походу уже не справляются со своей задачей поэтому только замена манжетов спасет... "я так думаю" :roll:


03 сен 2012, 17:25
Профиль
Показать сообщения за:  Поле сортировки  
Ответить на тему   [ Сообщений: 69 ]  На страницу Пред.  1, 2, 3, 4  След.

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 12


Вы не можете начинать темы
Вы не можете отвечать на сообщения
Вы не можете редактировать свои сообщения
Вы не можете удалять свои сообщения
Вы не можете добавлять вложения

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by STSoftware for PTF.
Русская поддержка phpBB